Manual
download PDFGetting started
CLAVE plays eight drum channels, each with its own euclidean pattern. You pick a channel with its pad and shape it with the encoder and the knobs.
Quick start
- Press play: the pattern starts.
- Turn up the master knob (overall volume).
- Touch a pad (1–8) to choose the channel you want to edit.
- Turn the encoder to change the number of hits (K).
- pitch knob = tuning · level knob = volume of that channel.
The 8 channels
| 1 | Kick |
| 2 | Snare |
| 3 | Closed hi-hat |
| 4 | Low tom |
| 5 | Conga |
| 6 | Cowbell |
| 7 | Maracas / shaker |
| 8 | Clap |
Each pad selects its channel and its LED shows the channel colour. The pad of the channel you are editing stays lit, at half brightness if that channel is muted. The pitch knob has a centre zone that snaps to the sample's original tuning; its LED tells you when you are there. Sequence length is global (1–16, 16 by default).
Controls
Every control does one thing on its own and another while you hold a modifier. Read across the row: the control, then what it does alone and under each of the three modifiers.
| Control | On its own | + shift | + tempo | + mute |
| play | Play / stop | Record automation (short) / clear it (2 s) | — | — |
| tempo | Tap the tempo in quarter notes | Double tempo (2x) | — | — |
| encoder | Hits K, or the cursor in linear mode | Accents: how many | BPM, fine adjust | Effect amount (wet) |
| swEnc + encoder | Rotate the pattern | Rotate the accents | — | Effect mode (16) |
| swEnc 2 s + encoder | Sequence length (1–16) | — | — | — |
| swEnc (press) | — | Accent the step under the cursor, linear mode only | — | — |
| pitch knob | Tuning | Accent amount, see "Accents" | Channel probability | LP filter cutoff |
| level knob | Volume (velocity) | Pan | — | LP filter resonance |
| pad 1–8 | Choose the active channel | — | — | Mute that channel |
| preset | Load (short) / save (2 s) | Kit selection mode | — | — |
| master knob | Overall volume | — | — | — |
A dash means the combination does nothing. The pitch and level knobs always act on the active channel, the one you picked with a pad.
Patterns
Each channel spreads its hits evenly over the sequence (euclidean mode), or plays the steps you place by hand (linear mode).
Probability
tempo + pitch knob: 16 = every hit plays · 0 = none · in between = random hit by hit, changing every lap without altering the euclidean pattern.
Sequence length
Hold swEnc 2 s: the ring turns amber; turn to choose 1–16 and press swEnc to exit.
Linear mode
shift + mute: place the steps by hand. The encoder moves the cursor and swEnc turns the step under the cursor on or off. It works per channel, so you can have some channels euclidean and others linear in the same song.
Accents in linear mode
In euclidean mode accents spread themselves out, like the hits. In linear mode you draw them: hold shift and press the encoder on the step you want to accent. If that step was off it turns on — an accent without a hit makes no sound.
Changing mode erases nothing
Going from euclidean to linear you inherit the hits and accents exactly as they were playing. Going back to euclidean, the channel keeps playing what you drew: the formula only takes over again when you ask it to spread things out, that is when you add or remove hits, rotate, or change the number of accents.
Accents
shift + encoder sets how many accents the channel has, and shift + swEnc + encoder rotates them. To have no accents at all, set the number of accents to 0.
Accent amount
shift + pitch knob sets the accent amount (0–12) for the active channel, and what it does depends on the channel:
| Channels | What an accent does | The knob controls |
| 1 kick · 2 snare · 3 hi-hat · 7 shaker · 8 clap | Accented hits play at full volume | How much the non-accented hits drop: from −3 dB (left) to −12 dB (right) |
| 4 tom · 5 conga · 6 cowbell | Accented hits play at full volume and higher in pitch | How many semitones the accent goes up (0–12) |
Presets
96 slots in 6 banks of 16. Three factory banks — euclidean (green), hip hop (orange) and latin (yellow) — and three of your own: blue, purple and cyan, 48 slots you can save to. The factory banks live in the firmware: they can't be overwritten and they never take up your saving space.
Loading and saving
preset short loads, preset held 2 s saves. When loading and saving, used slots are lit and empty ones are dark. While saving, shift + swEnc empties the slot.
Your presets are kept in their own area of memory (256 KB), so all 48 fit with room to spare. If a save ever fails, the ring flashes red.
What a preset stores
For the 8 channels: pattern (K, rotation, accents), pitch, velocity, pan, linear mode, double tempo and probability; plus the sequence length and the automation.
Not stored in the preset, because they are global: the kit, the effect and the mute state.
Preset tempo
Every preset stores its own tempo, but only imposes it if you load it while the machine is stopped: loading a preset then is choosing the tempo you are about to start with. While playing, the BPM you already have wins, so changing preset live never breaks the pulse, and stop/play doesn't move it either. Factory presets carry no tempo of their own and respect yours.
Backing up presets to your computer
The Backup presets page of the webflasher can read every preset you saved, download them as a .txt file and load them back into CLAVE, each one into the slot it came from. Slots that are not in the file are left alone. The machine must be stopped. Older backup files (firmware 3.0) can't be loaded back: they don't contain the whole preset.
Drum kits
There are 9 kits: 5 factory ones (green on the ring) and 4 user ones (purple, only if they have content). The chosen kit is remembered at power-up.
Choosing a kit
| shift + preset | Enter and leave kit selection mode |
| encoder | Browse the available kits (ring) |
| swEnc | Load the highlighted kit and exit |
Uploading your own kits
From the Upload Sound Kits page of the webflasher you can preview 8 samples (one per channel) and save them to a user slot (1–4). They stay in the machine when you turn it off.
How to prepare your samples
- Mono WAV, 44.1 kHz, 16 or 24 bit. Whatever you upload ends up mono, 44.1 kHz, 16 bit.
- Up to 3 s per sound and about 14 s in total for the 8 sounds of the kit. Shorter is better.
- No silence at the start, so the hit doesn't arrive late.
- Normalize close to 0 dB: the page doesn't change the volume.
- A short fade-out at the end is added by the machine, so a sample that ends abruptly or gets cut at 3 s won't click.
- The output is stereo: each channel has its own pan.
Effects
16 modes. Cycle through them with mute + swEnc + encoder (one LED lights up in the colour of the effect) and set the amount (wet) with mute + encoder. Only one effect is active at a time and it is global: it is not saved in the preset.
Delay and reverb — 8 modes
All of them light the LED in magenta:
| Room | reverb only (short) |
| Hall | reverb only (long) |
| Delay 1/8 | delay only |
| Delay 1/4 | delay only |
| Dub | dark delay + reverb |
| Slap+Room | slap + short reverb |
| 1/4+Hall | delay + long reverb |
| Ambient | delay + wide reverb |
The amount rises gradually (1 click ≈ 0.2%, half bar ≈ 16%, full bar 65%), so the small settings are usable on a drum machine, where a little goes a long way.
Processing effects — 8 modes
Each one has its own LED colour:
| orange | SP404 | Warm saturation / compression |
| red | Distortion | Aggressive clipping |
| cyan | Bitcrush | Fewer bits and lower sample rate (lo-fi) |
| green | Comb | Resonant comb filter, tuned to the tempo |
| blue | Short flanger | Narrow sweep, synced to the tempo |
| purple | Fast flanger | Wide, fast sweep, synced |
| yellow | Marked tremolo | Rhythmic gate in eighth notes: it silences the slice |
| pink | Stutter | Beat repeat in sixteenths: it records a slice and repeats it |
They work on the signal coming in: if the overall volume is low, turn the master knob up to hear them properly.
Stutter and marked tremolo are opposites over the same pulse. The stutter records a slice of the master — the figure of the current tempo — and repeats it: during the slice it captures, the signal passes through live, and the following ones play back what it just recorded, so the effect is always made of what you have just played. Its amount sets how many slices go in a group (2 to 8), and the group re-syncs at the start of every bar. The tremolo does the opposite: instead of repeating the slice it silences it, and there the amount is the depth — at the minimum nothing is attenuated, at the maximum the silent half-eighth is total.
Filter and compressor
Resonant LP filter: mute + pitch knob (cutoff) and mute + level knob (resonance). It affects the whole mix, before the effects. Master compressor: always on internally.
Automation
Records 2 bars of pitch (per channel) and of the filter, looping.
Recording and clearing
| shift + play short | Start recording (the channel LED blinks) |
| play | Leave recording — the automation keeps playing |
| play again | Stop |
| shift + play 2 s | Clear the lane you are looking at |
| shift + play + encoder click | Clear everything |
While you record one channel, the automation of the others keeps playing. The filter is only recorded if you move it. Probability is not automated: it is a fixed value per channel.
Clearing works on what you are seeing. With no modifier it clears the pitch of the active channel; while you hold mute and look at the filter or at the effect, it clears that lane. The whole ring blinks in the colour of what was cleared. To wipe every lane at once — the pitch of all eight channels, the filter and the effects — hold shift and play and click the encoder: the ring blinks red, longer. When you clear the effects lane the amount goes back to the last value you set by hand, not to the one the automation left or to zero.
Connections and sync
⚠️ Only connect sync in with CLAVE powered on, and if the clock comes from a passive multiple use a buffered one (or a dedicated output on your clock): CLAVE's input can load the signal and disturb the other modules.
Jacks and ports
| Audio | 1 × 3.5 mm stereo jack (output) |
| Clock sync | 2 jacks: in and out |
| USB-C | 2 ports: power, and data / MIDI |
| Power | 5 V over USB-C |
Clock input
CLAVE works out the resolution on its own: 1, 2, 4 or 24 pulses per quarter note (PPQN). For 1, 2 and 4 PPQN it picks the one that puts the tempo between 80 and 160 BPM. If your tempo is outside that range (170 BPM would read as 85, for example), tap TEMPO in quarter notes with the clock connected: CLAVE picks the resolution that matches your tap and remembers it.
It follows the tempo even while stopped, and when you press play it starts on the next pulse, in time. If the master changes BPM, CLAVE follows within one or two pulses; the more PPQN your clock sends, the tighter the tracking.
Clock output
2 PPQN (one pulse every two steps), 50% square wave, steady tempo. Low while stopped; 3.3 V logic. Two CLAVEs chain directly: sync out of one into sync in of the other.
MIDI clock over USB
CLAVE also follows external MIDI clock over USB (24 PPQN); while USB clock is present the jack input is ignored.
While connected to the computer
When one of the webflasher pages is connected to CLAVE and the machine is stopped, the ring breathes slowly in orange: that means "connected". While presets or samples are loading, the ring fills up like a progress bar, and a green flash means it finished. Press play and the ring goes back to showing the sequence, so you can try a kit while still connected.
MIDI
CLAVE speaks USB MIDI both ways over the data port: it can drive a DAW or another machine with its patterns, and it can be played from a pad controller or a keyboard.
CLAVE as a sequencer
Every hit that sounds goes out as a note on channel 10. The eight channels are notes 36 to 43, in their own order:
| Note | Channel | Note | Channel | |
| 36 | 1 Kick | 40 | 5 Conga | |
| 37 | 2 Snare | 41 | 6 Cowbell | |
| 38 | 3 Closed hi-hat | 42 | 7 Maracas | |
| 39 | 4 Low tom | 43 | 8 Clap |
They are consecutive on purpose: in a drum rack they fall as a 2×4 block in the resting view, with nothing to scroll.
The accent travels as velocity: an accented hit sends 127, a normal one between 90 and 32 depending on where you leave the accent amount. That holds for all eight channels, including the three where the machine plays the accent as a jump in pitch. A muted channel sends nothing, and nothing is left hanging when you stop.
What crosses and what does not. Everything that decides whether and when a hit sounds goes to MIDI: the pattern, the rotation, probability, mute, swing, the accent and the transport. Everything that decides how it sounds stays in the machine: pitch, kit, reverb, delay, filter, volumes and pan. As a controller CLAVE is an eight-track euclidean sequencer with dynamics, and the instrument is at the other end.
The knobs as CC
The 18 controls send CC, so you map them once with MIDI learn and save it as a template:
| Control | CC |
| Level, channels 1–8 | 20–27 |
| Master filter: cutoff / resonance | 30 / 31 |
| Pitch, channels 1–8 | 40–47 |
CLAVE's knobs are not one per channel: there is one pitch knob and one level knob, and they act on the active channel. So the CC number depends on the layer you have selected — move the pitch knob with the kick selected and it goes out on the kick's CC; step into the snare and the same knob goes out on its own. They are sent only when the value changes, and only while the knob is actually moving. In Ableton the input needs both Track and Remote switched on.
Note that the knobs keep acting on CLAVE's own sound, so moving a CC also moves what the machine plays.
Playing CLAVE by hand
A pad controller or a keyboard plugged into the data port can play the eight voices: notes 36 to 43 again, on any MIDI channel, so there is nothing to configure on the controller. It sounds with the sequencer stopped and also on top of the pattern. The velocity of the pad scales the level of that channel, so the level you set is the ceiling and a soft hit sounds soft. A muted channel still sounds when you play it by hand — the mute belongs to the sequencer, not to your finger.
For this, CLAVE has to start up with the controller already connected: plug it into the data port, power CLAVE from the other USB-C port, and then switch it on. The ring flashes green once the controller is ready. One device at a time, and while it is connected the webflasher pages are not available.
Power-up combos
Hold the buttons while you plug in the USB (or while you reset). The light of the mode comes on as soon as the machine sees the combination, even if you are still holding it. To leave and carry on booting, click the encoder (swEnc); if you don't touch anything it leaves on its own after 30 s. Every setting is stored: it survives power-off.
All the combos
| shift + play | Download mode, to install firmware from the browser (this one enters on its own) |
| swEnc | Reverse the encoder direction (release it, then click again to carry on) |
| shift + tempo | LED brightness: turn the encoder and leave with a click |
| preset + play | Colour-blind palette |
| mute + play | Left-handed mode |
| play + tempo | Start-up preset: random or the last one used |
Brightness
The ring, the indicators and the pads dim together. Useful for playing in the dark or for recording video. The maximum is 50%, because the LEDs are what draws the most current and above that the touch sensor can lose power. Colours stay readable all the way down to the minimum.
Colour-blind mode
Swaps the colours of the eight channels for a palette that can be told apart with any kind of colour blindness, and keeps the two that could still be confused as far apart as possible on the ring. An accent stops being a complementary colour and becomes the same colour, brighter.
Start-up preset
By default CLAVE powers up with a random factory preset, so you don't always hear the same rhythm — nothing is lost, your own presets are still in their slots. Hold play + tempo while plugging in to switch to the last preset you used, and hold it again to go back to random.
Left-handed mode
Bars are drawn from the top towards the right. By default they start at the bottom and climb up the left side, because your right hand covers the right side of the ring when you turn the encoder.
Buttons and LEDs
What each light on the panel is telling you.
Buttons
| play | play / stop |
| preset | load / save |
| tempo | tap tempo |
| mute | mute and effects |
| shift | modifier |
| swEnc | encoder switch |
The 16-LED ring
The steps of the active channel, in its colour. Accents use a different colour and empty steps stay dark. The white playback cursor only appears while playing; stopped, you see the real state of every step. In linear mode a dot also marks where the encoder cursor is.
Bars and the mute view
The bars — effect, filter, probability, tempo, accents, length — start at the bottom and climb up the left side, so your hand doesn't cover what you are adjusting. The mute view uses that same left half: one LED per channel, lit if it sounds.
The 4 indicators
Original pitch · sequence mode of the channel · reserved · automation (blinks while recording, steady while playing back; in the preset and kit views it shows the bank).
The 8 pad LEDs
In the mute view they show which channel sounds. Outside it, they mark the channel you are editing.
Updating the firmware
Connect the machine over USB and open the webflasher in desktop Chrome, Edge or Brave (it does not work in Firefox or Safari): clave.oficinadesonido.org. Kits and presets are uploaded from there too.
Installing
To put the machine in download mode, hold shift + play while you plug the USB cable in. The version a page installs is shown next to its Install button.
Keep your presets and kits
Before installing, the browser asks whether to erase the device and shows an Erase device checkbox. Leave it unchecked: the installer then writes only the firmware and your presets and saved kits stay in place. If you tick it, everything is wiped.
What changed since 3.0
If you are coming from the first public firmware:
- Accents work on every channel. Before, the amount knob did nothing on channels 1, 2, 7 and 8, and on the hi-hat it swapped the accent for a fixed 808 sound.
- Presets have their own memory. Up to 3.4 they shared the settings memory and filled it up after about 25, and the ones past that were lost on the next restart.
- Reverb and delay amount: a full bar is about 25% of what it used to be, and it rises gradually. The processing effects are unchanged.
- Clock input detects 1, 2, 4 or 24 PPQN on its own and follows tempo changes.
- Brightness tops out at 50%, so the touch sensor doesn't lose power.
- Samples get an automatic fade-out, and the webflasher shows progress on the ring.
- Pitch knob: it no longer drifts on its own at the edge of the snap zone, and leaving the zone moves by one semitone instead of two.
- Filter and effects: the master filter runs on the mix before the effects, so filter + reverb no longer breaks up.
- Kick and toms: no more click when a sound retriggers while its tail is still ringing.